How a Cut Feels vs. How It Looks: Four Scissor Tests on Facial Tissue

How a Cut Feels vs. How It Looks: Four Scissor Tests on Facial Tissue

LeGrand Editorial Team

THE QUESTION

Across four cutting tasks on 1-ply and 3-ply facial tissue, did the way two used pairs of scissors felt during cutting match how the finished cuts looked?

THE SHORT ANSWER

Across 48 attempts in four cutting tasks on 1-ply and 3-ply facial tissue, how a cut felt did not always match how it looked afterward. In 1-ply tissue, the LeGrand 9-inch dressmaker scissors and a rainbow-colored comparison pair made similar-looking tip slits, but the comparison pair felt stiffer to open and close. During the 3-ply wave test, the LeGrand pair felt harder to use near the end, and a close-up showed a comparatively smooth section of its cut edge. The comparison pair felt relatively easy to turn, and a close-up showed a narrow, pointed projection along one of its curves.

How a Cut Feels vs. How It Looks: Four Scissor Tests on Facial Tissue

Each test focused on one task, from starting a straight cut to guiding the scissors around a circle. Putting the four tests together lets us compare what the operator noticed during cutting with what we could see afterward.

FOUR CUTTING TASKS AT A GLANCE

We used the same two pairs throughout: LeGrand’s Japanese Dressmaker Scissors for Fabric Cutting – High-Carbon Stainless Steel 9” and a rainbow-colored comparison pair of unknown make and model. Both pairs had been used before testing.

We tested one household facial tissue product in two forms: a single ply separated from the original sheet and an intact 3-ply sheet. One operator performed the tasks in the order shown below. Each pair made three attempts per ply condition, for 12 attempts per task and 48 overall. Each repeated tip-cut attempt included several slits.

Test 06 · Straight Cuts
The LeGrand pair started and completed every straight cut. With the rainbow-colored pair, the cut failed to start at the initial position in two of three 1-ply attempts, and the operator moved to a new position before continuing. The 1-ply overview photo shows two of the three sheets and includes one section that remained partly connected. The rainbow-colored pair completed all three 3-ply cuts, and small steps were recorded along all three cut lines.

Test 07 · Repeated Tip Cuts
The two pairs made broadly similar-looking slits in the 1-ply photographs. The operator found the LeGrand pair light to open and close and the rainbow-colored pair stiffer to operate.

Test 08 · Wave-Like Curves
During the 3-ply test, tissue clung to the LeGrand blades near the end and the operator found it harder to continue. A photographed section of the LeGrand edge looks comparatively smooth. The rainbow-colored pair felt relatively easy to turn, and one photographed edge shows a narrow, pointed projection.

Test 09 · Circles
Both pairs felt easier to guide through intact 3-ply tissue than through a separated single ply. The rainbow-colored pair felt relatively easy to guide in 3-ply, yet the close-ups show small pointed protrusions along the inspected edges.

WHEN SIMILAR-LOOKING CUTS FELT DIFFERENT

In the repeated tip-cut test, both pairs made short slits along the tissue edge. The 1-ply close-ups show rows of slits that look much alike. Making them felt different. The operator found the rainbow-colored pair stiffer to open and close and reported more hand fatigue during the repeated cuts.

Close-up of short slits in 1-ply facial tissue cut with LeGrand scissors, with some strips curling at the edge.

Close-up of short slits in 1-ply facial tissue cut with rainbow-colored scissors, with several strips curling upward.

WHEN CUTTING FEEL AND EDGE SHAPE DIVERGED

During the 3-ply wave test, loose tissue clung to the LeGrand blades toward the end, and the operator found it harder to continue. The selected close-up shows a comparatively smooth section of the cut edge. We could not match the section shown in that photo to the point where the operator felt the cut become harder.

The rainbow-colored pair felt relatively easy to redirect in the same test. One close-up shows a narrow, pointed projection interrupting the curve.

Close-up of a broad curve cut into 3-ply facial tissue with LeGrand scissors.

Detail of a curved cut in 3-ply facial tissue made with rainbow-colored scissors.

STARTING, STEERING, AND FINISHING A CUT

In the straight-cut test, the rainbow-colored pair presented different difficulties in the two ply conditions. In 1-ply, the operator sometimes had to move the scissors before the cut would begin. In 3-ply, the operator completed every cut with that pair but felt the cutting position shift between strokes. The small steps recorded along all three cut lines are a detail that a count of completed cuts would miss.

The circle test showed how steering felt with each ply condition. Both pairs felt easier to guide through intact 3-ply tissue. Even so, the operator noticed a protrusion they had not expected in a 3-ply circle cut with the rainbow-colored pair. In 1-ply, the same pair was harder to start and steer, and the photographed arc showed local irregularities. The 1-ply wave test also paired harder steering with more angular transitions in the photographed edges.

WHAT CUTTING RESEARCH CAN TELL US

Mahvash and colleagues (2008) modeled scissor-cutting forces as a material deforms and separates. They measured friction between the blades separately by closing the scissors without a sample. Their experiments used robot-operated surgical scissors to cut clamped strips of paper, plastic, cloth, and chicken skin.

That work gives context for the different forces that can contribute to how scissors feel in use. Our facial tissue tests recorded the operator’s impressions and the appearance of selected cuts. They did not measure force or isolate the source of the resistance.

WHAT TO LOOK FOR WHEN JUDGING A CUT

When trying scissors on facial tissue or another thin, flexible sheet, check whether the cut starts where you place the blades. As you go, notice the effort needed to open, close, or turn the scissors, and watch for material that shifts or clings to the blades. Then look closely at the finished cut. Check for sections that stayed attached and for small steps or points along the edge.

RESEARCH REFERENCES

Mahvash, M., Voo, L. M., Kim, D., Jeung, K., Wainer, J., & Okamura, A. M. (2008).
Modeling the Forces of Cutting with Scissors.
IEEE Transactions on Biomedical Engineering, 55(3), 848–856. 

← Older Post

WHAT WE NOTICED

The rainbow-colored pair sometimes needed to be repositioned before a 1-ply straight cut would start. In the 3-ply wave test, tissue clung to the LeGrand blades near the end. When cutting circles, both pairs felt easier to guide through intact 3-ply tissue than through a separated single ply.

WHAT THIS TEST SUGGESTS

Check how the cut starts, how the scissors feel as you guide them, and how the cut looks afterward. A similar-looking result can take different effort, and a cut that feels easy can still leave a visible irregularity.

LIMITS OF THIS TEST

One operator used two previously used pairs of scissors on one facial tissue product in 48 attempts across four tasks. The operator knew which pair was in use and reported how the scissors felt. The tests did not measure cutting force, blade friction, or edge geometry. The photographs show selected samples or sections of cut edges. The findings apply to the tools and tissue tested here.